View XD-402_7328137.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

b60-4202-00 00 ma (k,p,y,m,x,t,q,e2) mc 9809 compact hi-fi system instruction manual kenwood corporation xd-series digital audio digital audio compact compact text xd-502/xd-552/xd-572s XD-402/xd-452 this instruction manual is used to describe multiple models listed above. model availability and features (functions) may differ depending on the country and sales area. ? free datasheet http:///
xd-series (en) 2 preparation section before applying power caution : read this page carefully to ensure safe operation. for the united kingdom factory fitted moulded mains plug 1.the mains plug contains a fuse. for replacement, use only a 13-amp asta-approved (bs1362) fuse. 2.the fuse cover must be refitted when replacing the fuse in the moulded plug. 3.do not cut off the mains plug from this equipment. if the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. if nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. important: the wires in the mains lead are coloured in accordance with the following code: blue : neutral brown : live do not connect those leads to the earth terminal of a three- pin plug. safety precautions warning : to prevent fire or electric shock, do not expose this appliance to rain or moisture. caution: to reduce the risk of electric shock, do not remove cover (or back). no user-serviceable parts inside. refer servicing to qualified service personnel. risk of electric shock do not open the lightning flash with arrowhead symbol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. the exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. caution *ac voltage selection the ac voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. before connecting the power cord to your ac outlet, make sure that the setting position of this switch matches your line voltage. if not, it must be set to your voltage in accordance with the following direction. ac voltage selector switch move switch lever to match your line voltage with a small screwdriver or other pointed tool. note: our warranty does not cover damage caused by exces- sive line voltage due to improper setting of the ac voltage selector switch. md/dvd i nput digital out optical ac 220- 240v~ ac 110- 120v~ ac 220- 240v~ ac 110- 120v~ ac 220- 240v~ ac 110- 120v~ ac 220- 240v~ ac 110- 120v~ the marking is located on the rear panel and says that the component uses laser beams that have been clas- sified as class 1. it means that the unit is utilizing laser beams that are of a weaker class. there is no danger of hazardous radiation outside the unit. class 1 laser product the marking of products using lasers (except for some areas) units are designed for operation as follows. europe and u.k. ................................................. ac 230 v only china and russia .............................................. ac 220 v only *other countries ........... ac 110-120 / 220-240 v switchable u.s.a. and canada ............................................ ac 120 v only austraria ............................................................. ac 240 v only free datasheet http:///
preparation section xd-series (en) 3 contents preparation section application section knowledge section before applying power .............................. 2 safety precautions ...................................... 2 important safeguards ........................ 4 special features ............................................... 6 handling of discs and tapes ............................ 7 system connection........................................... 8 accessories ....................................................................... 8 connection of the system accessories ........................ 8 connection with other components (optional or com- mercially-available equipment) ................................... 10 controls and indicators ................................. 12 main unit .......................................................................... 12 display .............................................................................. 14 remote control unit ........................................................ 15 operation of remote control unit .................. 16 channel space setting ................................................ 16 operation of jog dials ..................................... 17 let's put out some sound................................ 18 basic use method ............................................................ 18 playback of cd ................................................................ 20 playback of tape .............................................................. 22 searching for the desired music program (dpss) ... 25 receiving broadcast station .......................................... 26 let's record ...................................................... 28 recording on tape ......................................................... 28 copying tape (tape dubbing) ......................................... 31 playback of cd................................................ 32 listening in the desired sequence (program playback) ................................................... 32 repeated playback ......................................................... 34 random playback ............................................................ 36 r.d.s. (radio data system) (for u.k., europe and russia) .................................. 37 searching for a desired program type (pty search) ................................................................ 38 to be able to listen to the desired information at any time (eon)............................................................. 40 convenient cd recording ............................... 42 selection of the recording type .................................. 42 recording only desired titles (cd one track recording) ................................. 43 recording of an entire cd (cd direct recording) .......................................... 44 recording the programmed titles (cd program recording) .................................... 45 effective sound adjustment ......................... 46 balance adjustment......................................................... 46 input level adjustment ....................................................47 listening to music with desired tone and sound field/ switching the display (equalizer effect and 3d surround effect) ................................................................................. 48 creation and memorizing of an equalizer pattern ..... 49 clock adjustment............................................. 50 timer operation............................................... 51 sleep timer (sleep) ......................................................... 51 operate easy to use timer (o.t.t.) ................................ 52 timer programming.......................................................... 53 important items ............................................... 56 maintenance .................................................................... 56 reference ......................................................................... 56 in case of difficulty ........................................ 57 specifications ................................................. 61 before applying power caution : read the pages marked carefully to ensure safe operation. basic section basic section application section knowledge section as an e nergy s tar ? partner, kenwood corporation has determined that this products meets the e nergy s tar ? guidelines for energy efficiency. this product can save energy. saving energy reduces air pollution and lowers utility bills. free datasheet http:///
xd-series (en) 4 preparation section important safeguards please read all of the safety and operating instructions before operating this appliance. adhere to all warnings on the appliance and in the instruction manual. follow all the safety and operating instructions. these safety and operating instructions should be retained for future reference. 1. power sources C the appliance should be connected to a power supply only of the type described in the instruction manual or as marked on the appliance. if you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. for appliances intended to operate from battery power, or other sources, refer to the instruction manual. 2. power-cord protection C power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 3. caution C polarization C this appliance may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). this plug will fit into the power outlet only one way. this is a safety feature. if you are unable to insert the plug fully into the outlet, try reversing the plug. if the plug should still fail to fit, contact your electrician to replace your obsolete outlet. do not defeat the safety purpose of the polarized plug. 4. ventilation C slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the appliance and to protect it from overheating, and these openings must not be blocked or covered. the appliance should be situated so that its location or position does not interfere with its proper ventilation. to maintain good ventilation, do not put records or a table-cloth on the appliance. place the appliance at least 10 cm away from the walls. do not use the appliance on a bed, sofa, rug or similar surface that may block the ventilation openings. this appliance should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. 5. water and moisture C the appliance should not be used near water - for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc. never pull or stretch the cord. 6. temperature C the appliance may not function properly if used at extremely low, or freezing temperatures. the ideal ambient temperature is above +5c (41f). 7. heat C the appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 8. electric shock C care should be taken so that objects do not fall and liquid is not spilled into the enclosure through openings. if a metal objects, such as a hair pin or a needle, comes into contact with the inside of this appliance, a dangerous electric shock may result. for families with children, never permit children to put anything, especially metal, inside this appliance. 9. enclosure removal C never remove the enclosure. if the internal parts are touched accidentally, a serious electric shock might occur. 10.magnetic fields C keep the appliance away from sources of magnetic fields such as tv sets, speaker systems, radios, motorized toys or magnetized objects. 11.cleaning C unplug this appliance from the wall outlet before cleaning. do not use volatile solvents such as alcohol, paint thinner, gasoline, or benzine, etc. to clean the cabinet. use a clean dry cloth. 12.accessories C do not place this appliance on an unstable cart, stand, tripod, bracket, or table. the appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the appliance. any mounting of the appliance should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. an appliance and cart combination should be moved with care. quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. caution :read this page carefully to ensure safe operation. free datasheet http:///
preparation section xd-series (en) 5 13.lightning C for added protection for this appliance during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. this will prevent damage to the appliance due to lightning and power-line surges. 14.abnormal smell C if an abnormal smell or smoke is detected, immediately turn the power off and unplug the appliance from the wall outlet. contact your dealer or nearest service center. 15.damage requiring service C the appliance should be serviced by qualified service personnel when: a. the power-supply cord or the plug has been damaged. b. objects have fallen, or liquid has been spilled into the appliance. c. the appliance has been exposed to rain or water. d. the appliance does not appear to operate normally by following the instruction manual. adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to its normal operation. e. the appliance has been dropped, or the enclosure damaged. f. the appliance exhibits a marked change in performance. 16.servicing C the user should not attempt to service the appliance beyond that described in the instruction manual. all other servicing should be referred to qualified service personnel. 17.outdoor antenna grounding C if an outside antenna is connected to the appliance, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. article 810 of the national electrical code ansi/nfpa 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. see figure. 18.power lines C an outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. when installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 19.ac outlets C do not connect other audio equipment with a power consumption larger than that specified to the ac outlet on the rear panel. never connect other electrical appliances, such as an iron or toaster, to it to prevent fire or electric shock. 20. overloading C do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 21. attachment C do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 22. replacement parts C when replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. unauthorized substitutions may result in fire, electric shock, or other hazards. 23. safety check C upon completion of any service or repairs to this appliance, ask the service technician to perform safety checks to determine that the appliance is in proper operating condition. example of antenna grounding as per national electrical code antenna discharge unit (nec section 810-20) power service grounding electrode system (nec art 250, part h) ground clamp antenna lead in wire ground clamps nec C national electrical code grounding conductors (nec section 810-21) 1.item 3 is not required except for grounded or polarized equipment. 2.item 17 and 18 are not required except for units provided with antenna terminals. 3.item 17 complies with ul in the u.s.a. power off! important safeguards electric service equipment notes notes free datasheet http:///
xd-series (en) 6 preparation section special features demonstration when the power supply is restored after a power failure or the power cord is unplugged and plugged in again during use, this unit automatically starts the demonstration function (display only). during the demonstration, the display changes in sequence but the audio does not change. the large sound level meter represents the movement in music with brilliant colors to offer the joy of viewing the music at the same time as listening. 3d large-sized color display panel simplified operations using large-sized, twin jog dials this dial allows you to set the cd program and timer-related operations while observing the operating conditions shown by the display and icons. 3-disc carousel cd player three discs can be set. there are various ways for enjoyment at the time of program playback, repeat playback, random playback, etc. multi-control jog dial (right dial: for use in selecting a function) this dial allows you to reproduce realistic audio by setting and registering desired equalizer patterns as well as selecting the preset equalizer patterns. sound control jog dial (left dial: for use in selecting the tone and sound field) timer programming : timer playback, timer recording and ai timer playback can be pro- grammed. ? ai timer playback : when the unit is turned on by the timer, the sound level increases gradually. o.t.t. : timer with easy setting, which operates only once. sleep timer : useful when you want to go asleep while listening to music. convenient timer functions cd text information display (cd text compatibility) the text information (disc title and track titles) recorded in cds can be displayed. to cancel : turn the unit off (standby mode) and press the key. to switch over the demonstration : press the display/demo key during demonstration to stop it. each press of the key switches the demonstration as shown below. 1 demo on ...... (demonstration executed) 2 demo off ...... (demonstration canceled) display /demo free datasheet http:///
preparation section xd-series (en) 7 safety tab (accidental erasure prevention tab) after an important recording has been finished, break the safety tab, to prevent the recorded contents from being erased or recorded on accidentally. for b side for a side to store cassette tapes do not store the tapes in a place which is subject to direct sunlight, or near equipment that generates heat. keep the cassette tapes away from any magnetic field. to re-record apply tape only to the position where the tab has been removed. when there is slack in the tape in such a case, insert a pencil into the reel hole and wind the reel hub to remove the slack. n s 1.longer tape than 110 minutes cassette tape since longer tape than 110 minutes cassette tape is very thin, the tape could adhere to the pinch roller or be easily cut. it is recommended that these tapes not be used with this unit to prevent possible damage. 2.endless tapes do not use an endless tape, as this could damage the mechanism of the unit. notes notes notes on cassette tape handling of discs and tapes label side playing side cleaning if fingerprints or foreign matter become attached to the disc, lightly wipe the disc with a soft cotton cloth (or similar) from the center of the disc outwards in a radial manner. storage when a disc is not to be played for a long period of time, remove it from the player and store it in its case. handling hold the discs so that you do not touch the playing surface. disc handling precautions disc accessories the disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound quality or pro- tecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction. do not attach paper or tape to either the playing side or the label side of the discs. sticker sticky paste never play a cracked or warped disc during playback, the disc rotates at high speed in the player. therefore, to avoid danger, never use a cracked or deformed disc or a disc repaired with tape or adhesive agent. please do not use discs which are not round because they may cause a malfunction. discs which can be played with this unit cd (12 cm, 8 cm), and the audio part of cdv, cd-g, cd-eg and cd-extra. use discs that comply with the iec standard, for example a disc carrying the free datasheet http:///
xd-series (en) 8 preparation section accessories fm indoor antenna (1) am loop antenna (1) speaker cords (2) remote control unit (1) connection of the system accessories system connection the supplied antenna is for indoor use. place it as far as possible from the main system, tv set, speaker cords and power cord, and set it to a direction which provides the best reception. the accessory antenna is for temporary indoor use only. for stable signal reception we recommend us- ing an outdoor antenna. remove the indoor antenna if you connect one outdoors. 1 connect to the antenna terminal. 2 locate the position providing good recep- tion condition. 3 fix the antenna. fm indoor antenna am loop antenna unpacking unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. examine the unit for any possibility of shipping damage. if your unit is damaged or fails to operate, notify your dealer immediately. if your unit was shipped to you directly, notify the shipping company without delay. only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. we recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future. keep this manual handy for future reference. caution note on connection connect the components as shown in the diagram.only plug the power cord into a power outlet once connections are completed. the rear panel configuration is variable depending on the models (countries or area). use to adapt the plug on the power cord to the shape of the wall outlet. (accessory only for regions where use is necesary.) ac plug adaptor (1) 12 3 assemble. provided in the speaker package gnd fm 75 w am antenna gnd fm 75 w am antenna batteries (r6/aa) (2) free datasheet http:///
preparation section xd-series (en) 9 1.be sure to insert all connection cords securely. if their connections are imperfect, the sound may not be produced or noise may interfere. 2.before plugging or unplugging a connection cord, be sure to unplug the power cord from the wall ac outlet. if connection cords are plugged or unplugged with the power cord left plugged in, malfunction or damage may result. malfunction of microcomputer if operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to in case of diffi- culty. u twist speakers twist speaker unit main unit system connection notes notes caution regarding placement (except for u.s.a., u.s.-military and canada) speaker and tv installation if there is a magnet or other device generating magnetic force nearby, interaction between the magnet and speaker may cause color blotching on the tv. if this happens, move the speaker at least 20 cm away from the tv set. speaker (left) speaker (right) speaker cord ? ? ? never short-circuit the + and - speaker cords. ? if the left and right speaker connections or the + and - polarity are inverted, the sound will be unnatural with unclear positioning of musical instruments, etc. be sure to connect them without mistake. ls-n402 ls-n452 ls-n502 ls-n552 XD-402 xd-452 xd-502 xd-572s/xd-552 speaker model name system name be sure to adhere followings. or proper ventilation will be blocked causing damage or fire hazard. ? do not place any objects impairing heat radiation onto the top of unit. ? leave a space around the unit (from the largest outside dimension including projection) equal or greater than, shown below. top panel : 50 cm, side panel : 10 cm, back panel : 10 cm + - + - front speakers ( 6-16 w ) r l - + - + 1234 1234 caution regarding placement (for u.s.a., u.s.-military and canada) be sure to adhere followings. or proper ventilation will be blocked causing damage or fire hazard. ? do not place any objects impairing heat radiation onto the top of unit. free datasheet http:///
xd-series (en) 10 preparation section system connection connection with other components (optional or commercially-available equipment) optical-fiber cable (provided with the md recorder) md recorder, dvd player, vcr or analog turntable digital out jack (optical) cap remove the cap and plug the optical-fiber cable. optical-fiber cable ? insert the optical-fiber cable straight into the connector until it clicks. ? be sure to attach the protection cap when the connector is not used. ? never band or bundle the optical-fiber cable. audio input audio output md recorder/vcr dvd player/analog turntable (p-110/optional) in case an associated system component is connected, also read the instruction manual of the component. l r l r md rec output md/dvd input digital out optical audio output note note note caution note on connection connect the components as shown in the diagram.only plug the power cord into a power outlet once connections are completed. the rear panel configuration is variable depending on the models (countries or area). ? if an external component such as a dvd player is connected to the md/dvd input jacks, the md rec output jacks do not output the audio of the external component. digital out optical extremely low sound is played back powerfully. super woofer power cord to wall ac outlet + - + - front speakers ( 6-16 w ) super woofer pre out r l (except for u.s.a. and canada) (sw-500/optional) free datasheet http:///
preparation section xd-series (en) 11 system connection surround (rear) speakers this switch can be used only when the separately sold surround (rear) speakers are connected. when the switch is set to on, surround playback can be enjoyed. when this switch is set to off, normal playback is ex- ecuted. ? please operate this switch while the power is switched off. ? we recommend to keep this switch set to off when no surround (rear) speakers are connected to obtain a better sound quality. ? when the switch is set to off, no sound will come from the surround (rear) speakers. in regard to the surround switch 123 twist 4 twist speaker unit main unit -+ + - + - surround speakers ( 8-16 w ) r l @ on # off surround -+ rl surround switch @ on # off surround lead the 75 w coaxial cable connected to the fm out- door antenna into the room and connect it to the fm 75 w termimal. fm outdoor antenna use a commercially-available antenna adapter (a small-sized model). xd-5....series : except for u.s.a. amd canada xd-4....series : except for u.s.a., canada, u.k., europe and russia ? ? gnd fm 75 w am antenna 1 select the tuner input. 2 while holding the select key depressed, turn the sound control jog dial to select the system mode. select 1 polar system 2 pilot tone system 3 establish the selection. polar pilot reception mode switching of fm broadcast (for russia) when you want to receive an fm broadcast in pilot tone mode, changing the setting as follows. enter 1234 s o u n d c o n t r o l free datasheet http:///
xd-series (en) 12 preparation section 3 phones auto reverse direct program search system a play b rec/ play auto reverse direct program search system menu disc skip 0 push open mini hi-fi component system xd-552 rds tp pty eon ta ex.bass select enter input display /demo mic vol min. max. mic back band tuning mode 1 @& # rev mode rec/arm tape eq. 0 push open a b disc 3 disc 0 open news & ^ 1 disc 2 r d s ( 3 1 & ! 9 0 7 8 4 ) $ ^ a % 5 # | on/standby s o u n d c o n t r o l m u l t i c o n t r o l 2 6 tape eq. dolby nr * mic vol. mic vol. @ down down up volume control up standby timer controls and indicators main unit disc selector key the disc for playback (or recording) is selected. disc selector indicators (xd-5... series only) the indicators corresponding to the trays accommodat- ing discs light up. during playback of a cd, the indicator corresponding to the cd blinks. disc skip key the disc for playback (or recording) is selected. this is also used for insertion of a cd to the inside of the disc tray. disc tray ) three discs can be stored. | cd operation keys ) play/pause ( ^ ) key stop ( & ) key tray open/close ( 0 open) key ) the disc tray is opened and closed. xd-502/552/572s XD-402/452 cd player unit power (for u.s.a. amd canada) free datasheet http:///
preparation section xd-series (en) 13 controls and indicators 1 on/standby ( ) key * on/standby (power) key (for u.s.a. canada) * power on/off switching is executed. 2 standby indicator ( the indicator lights up when the power is set to the standby mode. timer indicator wt the indicator lights up together with the standby indicator when the power is set to the standby mode after having activated a timer program. 3 phones terminal * for connection of a headphone (optional). 4 sound control jog dial &i turn this dial to select or cancel the equalizer and 3d surround settings. 5 multi control jog dial & turn this dial to select optimum modes according to the desired operations. when the cd input is selected, this dial is used to skip tracks. when the tuner input is selected, this dial is used to select a station. 6 menu key & press to switch the mode set with the multi con- trol jog dial on or off. the item selected by this key is variable depending on the current operation mode. menu indicator (xd-5... series only) the indicator starts to blink when the menu key is pressed. 7 back key & press when setting a mode using the multi con- trol jog dial to return to the previous step and restart the operation from there. 8 display $ 9 icon indicators & (cd pgm, rec. , dubbing, audio, clock) when a mode is set using the multi control jog dial, the icon indicators corresponding to the current mode light up. 0 rds-related indicators (for u.k., europe and russia) ! tuner operation keys band key press to switch the receiving band. tuning mode key switches the tuning mode. @ volume control knob * this is used for volume adjustment. # input key * press to select the input source. when tape or cd is selected, playback starts automatically provided that a tape or disc has already been loaded. display/demo key 6i switches the displayed information. when power is standby: switches the demonstration on and off. $ ex. bass (extra bass) key ( switches the extra bass play on and off. ex.bass indicator (xd-5... series only) ( the indicator lights up when the extra bass is switched on. % select key &p used for setting of various modes or establishing a selection. when power is standby: used for displaying the time. (when this key is pressed while the timer indicator is lit, the prog. or o.t.t. indicator also lights up, the timer reservation setting mode is displayed, then the display returns to the previous condition.) ^ enter key & used for entering a selected mode in memory or execut- ing it. cassette deck unit & a deck cassette holder press the area marked 0 0 0 0 0 push open to load or eject a tape. * dolby nr key (xd-5...series only) ? dolby noise reduction on/off switching is executed. tape eq. key (xd-4... series only) press to switch the tape equalizer on and off. ( rev. mode key the reverse mode of the deck (both sides, repeated, one side) is switched. ) b deck cassette holder press the area marked 0 0 0 0 0 push open to load or eject a tape. cassette deck operation keys a play ( @ # ) keys stop ( & ) key fast forward and rewind ( 1 ) keys a a/b key a press to select the deck to be operated. (for russia) ? used as the beat cancel key during recording of lw broadcasting. rec/arm key ?? press to start recording. pressing the key during record- ing stops it after leaving a non-recorded space (blank) of about 4 seconds. receiver free datasheet http:///
xd-series (en) 14 preparation section display the displays given in this manual are approximations only. they may differ from what actually appears on the display. controls and indicators xd-502 / xd-552/ xd-572s XD-402 / xd-452 1 cassette deck-related indicators this section contains the cassette deck operation indi- cators. the indicated information includes the tape reverse mode and tape transport direction. 2 sound level meter the display varies according to the music or the opera- tions of the cd, tape, etc. during the volume adjustment, this meter displaysthe current sound level as a reference. 3 timer-related indicators 4 equalizer/3d surround/s. direct indicators 5 cd player-related indicators this section contains the cd play and pause mode indicators. it also shows the disc number being se- lected. 6 ex.bass indicator 7 pgm/rpt. indicators 8 tuner-related indicators 9 character information display displays the input selection, frequency, volume level, etc. 0 guideline blinks during the setting of an item using the jog dial. 0 9 8 1 4 2 3 5 7 6 0 9 1 5 2 3 4 6 7 8 1 cassette deck-related indicators this section contains the cassette deck operation indi- cators. the indicated information includes the tape reverse mode and tape transport direction. 2 sound level meter the display varies according to the music or the opera- tions of the cd, tape, etc. during the volume adjustment, this meter displays the current sound level as a reference. 3 timer-related indicators 4 equalizer/3d surround/s. direct indicators 5 cd player-related indicators this section contains the cd play and pause mode indicators. it also shows the track numbers in the current disc. 6 repeat/pgm indicators 7 sleep timer indicator 8 tuner-related indicators 9 character information display displays the input selection, frequency, volume level, etc. 0 guideline blinks during the setting of an item using the jog dial. free datasheet http:///
preparation section xd-series (en) 15 remote control unit controls and indicators the keys on the remote control unit with the same names as on the main unit have the same function as the keys on the main unit. 1 on/standby ( power) key * power on/off switching is executed. 2 rds-related keys (for u.k., europe and russia) ta/news key a used for automatic reception of transmissions of a certain content. rds disp. key the display contents are switched during reception of rds broadcasts. pty key ? this is used to specify the program type when search- ing for a station. 3 numeric keys used as number keys when the input is cd or tuner. 4 disc skip key 5 time key press to switch the time information on the cd player unit. 6 random key ? for cd playback, switching is executed between ran- dom playback and normal playback. 7 tape play ( 2 3 2 3 2 3 2 3 2 3 ) keys a 8 tape a/b key a? 9 back key & 0 select key & ! enter key & @ sound control key &i press to select or cancel the equalizer and 3d surround settings. # ex. bass key ( $ input key * % band key ^ text disp. key w press to switch the text information recorded in a cd text disc. & repeat key y used for repeated playback of a cd. * tuning ( 1 ) keys (cd/tape/tuner) when the cd or tape input is selected, press to fast forward or backward (rewind) the disc or tape. when the tuner input is selected, press to select a station. ( mute key ( this is used to mute the sound temporarily. ) menu key & cd play/pause ( 6 ) key ) stop ( 7 ) key )| a multi control/volume keys &* skip/preset call ( 4 , ) keys (cd/tuner) | the left and right keys have the same functions as the multi control jog dial on the main unit. when the cd input is selected, press to skip forward or backward on the disc. when the tuner input is selected, press to select preset station. the top and bottom keys are used to adjust the volume. for u.k., europe and russia : rc-552e other countries : rc-552 volume cd tape mute rc-552e remote control unit ex.bass time input band pty ta/news rds disp. power tape a/b random repeat text disp. tuning 6 1 2 3 4 5 6 7 8 9 0 +10 3 2 1 4 7 m u l t i c o n t r o l disc skip sound control 3 2 8 9 0 ! 4 5 6 7 ( * ) & a 1 menu back select enter @ # % $ ^ free datasheet http:///
xd-series (en) 16 preparation section operation of remote control unit loading batteries 1 remove the cover. 3 close the cover. ? insert two r6 (aa-size) batteries following the polarity indications. 2 insert batteries. operation plug the power cord into the mains power outlet and press the on/standby ( power) key of the remote control unit to turn power on. after the power has been turned on, press the desired key. to turn power off, press the on/standby( power) key again. the power mode enters the standby mode in which the standby indicator lights up. (the timer in- dicator also lights in this mode if a timer program has been activated.) ? when pressing more than one remote control keys successively, press the keys securely by leaving an interval of 1 second or more between keys. 1.the provided batteries are intended for use in operation checking, and their service life may be short. 2.when the remote controllable distance becomes short, replace both of the batteries with new ones. 3.if direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction may occur. in such a case, change the installation position to avoid malfunction. operating range (approx.) remote sensor 2 1 notes notes channel space freq. area 1 2 usa, canada and south american countries other countries fm : 100 khz am : 10 khz fm : 50 khz am : 9 khz the space between radio channels has been set to the one that prevails in the area to which the system is shipped. however, if the current channel space setting does not match the setting in the area where the sys- tem is to be used, for instance when you move from area 1 or area 2 shown in the following table or vice versa, proper reception of am/fm (mw/fm) broad- casts cannot be expected. in this case, change the chan- nel space setting in accordance with your area by re- ferring to the following table. channel space setting (except for the u.s.a., canada, u.k., europe, australia and russia) 1 select the tuner input. 2 while holding the select key depressed, turn the sound control jog dial to select the system mode. enter f0 m100/am1 f9 m 50/am select 30 ? 6m 30 ? ? the am display is variable depending on the model (country or area), and mw may be displayed in some areas. 1 fm100/am10 khz step, 2 fm 50 /am 9 khz step, 3 establish the selection. s o u n d c o n t r o l free datasheet http:///
preparation section xd-series (en) 17 operation of jog dials this unit has two jog dials named the multi control and sound control jog dials. the multi control jog dial makes it possible to set (establish) many functions in a simple procedure. when the menu key is pressed, the icon indicators light according to the multi control jog dial operation so you can select the desired mode based on a more intuitive method. 1 press the menu key to enter the multi con- trol setting mode. 2 select an operation mode by turning the multi control jog dial (or pressing the multi control keys on the remote control unit). 3 set, establish or execute (determine) items by pressing the select key and/or enter key. multi control jog dial sound control jog dial equalizer patterns and 3d surround levels that can be recalled rock .................. rock music disco ................. disco music pop .................... pop music movie ................ movie music jazz ................... jazz music classic ............... classic music custom eq 1 custom eq 2 custom eq 3 3d level 1 ......... 3d surround level 1 3d level 2 ......... 3d surround level 2 s. direct ............. pure sound can be repro- duced by bypassing the ex.bass, equalizer and 3d surround circuitry. effect off ............ normal playback ? to cancel the mode for setting (using) multi control , read the description of each item in this manual. ? press the back key to return to the previous step and restart operation from there. (the back key is inoperative once scrolling message press ' enter ' to start has been displayed.) ? with the remote control unit, pressing the menu key makes it possible to select the same items as those available on the main unit using the multi control keys. volume menu back select enter 4 7 m u l t i c o n t r o l ? pressing the sound control key on the remote control unit allows selection of same items as the sound control jog dial. icon indication example: when tape dubbing is selected with the multi con- trol jog dial (or the multi control key on the remote control unit), the dubbing icon indicator lights up. the following items can be selected by turning the multi control jog dial. the messages inside ( ) may not be displayed under certain situations. (cd program play) only when the cd input is selected (recording options) only when a tape is present in deck b (tape dubbing) only when the selected input is tape and tapes are present in both decks a and b audio options clock options in the multi control setting mode (while the guide- line is blinking), the band and play keys are defeated and inoperative. select enter back s o u n d c o n t r o l m u l t i c o n t r o l menu cd pgm rec. dubbing audio clock s o u n d c o n t r o l m u l t i c o n t r o l display examples equalizers manual memory created by the user the sound control jog dial (or the sound con- trol key on the remote control unit) makes it possible to select a tone or sound effect in an easy procedure. i free datasheet http:///
xd-series (en) 18 basic section 1. switching the power on (off) lets put out some sound ? the display shows a reference value. (the reference value is also shown visu- ally by the sound level meter.) 2. selecting the desired output when the power is on, pressing the on/standby key enters the power standby mode, in which the standby indicator lights up. 1 tuner (radio) 2 cd ) 3 tape a 4 md/dvd (external input) 0u muting the sound temporarily reproducing sound with enhanced bass 3. volume adjustment ? if you select the md/dvd (external input) mode, also read the instruction manual of the component connected to the md/dvd input jacks. listening through headphones insert the headphone plug into the phones jack. ? the sounds from all speakers are cut off. reproducing sound with enhanced bass basic use method input 2 2 down volume control up 3 3 r d s phones 1 1 2 2 3 3 1 1 on/standby on/standby power or free datasheet http:///
xd-series (en) 19 basic section muting the sound temporarily (remote control unit only) when cd has been selected. ? press again to resume the original volume. ? the sound muting is also canceled when the volume is controlled. let's put out some sound blinks ? each press switches ex.bass on and off alternately. ? the ex.bass is switched off automatically during recording or when the sound control jog dial is turned. lights c2 d01 1:1 ex.bass mute xd-5....series xd-4....series ex.bass volume display reproducing sound with enhanced bass (ex. bass) v9 olume 1 standby mode while the standby indicator of the unit is lit, a small amount of current is flowing into the unit to back up its internal memory. (the timer indicator also lights if a timer program has been activated be- fore entering the standby mode.) this condition is referred to as the standby mode of the unit. while the unit is in the standby mode, it can be turned on from the remote control unit. this unit has been designed to minimize power con- sumption. one-touch operation function the power can also be turned on by pressing the play key of the cd player, the play key of the cassette deck or the band key of the tuner. it is also possible to turn the power on by simply pressing the 0 open key. ? when the cd or tape input is selected and a disc has been loaded in the disc tray or a tape has been loaded in the deck for use in playback, playback starts at the same time. c0 d @ d1 0:0 free datasheet http:///
xd-series (en) 20 basic section let's put out some sound 1 open the tray. 2 place a disc. 3 close the tray. 1. load a disc. playback of cd the tray opens when the key is pressed and closes when the key is pressed again. 2. start playback. time high-speed search in forward and reverse directions to stop playback skipping tracks if a disc has already been loaded in the cd player and the power is off, simply pressing the cd play key turns power automatically on and starts playback. playback from desired track playback from desired track open 0 1 1 & ^ 2 2 disc played first when the ^ key is pressed. the label must be on top. c0 d01 0:0 the recorded track no. are shown. xd-5....series ? after a few seconds, play starts from track no.1. ? playback stops after having played all discs in the trays. (relay play) ? when the 0 open key is pressed during playback, the tray opens but the playback continues. (the disc skip key is inoperative at this time.) r d s 1 1 2 2 disc skip start playback/ to pause playback free datasheet http:///
xd-series (en) 21 basic section let's put out some sound the selected disc is indicated. time display on the cd player each press of the time key of the remote control unit switches the displayed time information. ? only the elapsed time of the track being played is displayed during program playback, random playback and single-track repeated playback. 1 2 3 4 c0 d01 0:0 lights when a disc is inserted at the time of playback. 2 1:1 @ 8 4:1 - 6 2:4 1 ? do not touch the played side of disc. ? rotate the tray with the disc skip key to insert the third disc. ? the tray containing the disc to be played should come to the front right position when the unit is seen from the front. xd-4....series ? playback starts from the position where the key is released. high-speed search in forward and reverse directions (remote control unit only) skipping tracks backward search forward search ? the tracks in the direction the dial is rotated are skipped, and the selected track will be played from the beginning. ? when the jog dial is rotated a little in the direction of counterclockwise once during playback, the track being played will be played from the beginning. ? the cd tracks can also be skipped using the 4 or key of the remote control unit. to skip backward to skip forward tuning 1 m u l t i c o n t r o l to stop playback ? each press pauses and plays the cd alternately. to pause playback playback from desired track press the numeric keys as shown below.... to select track no. 23 : 003 to select track no. 40 : 0000) (main unit) (remote control unit) & ^ disc skip 1 disc disc 3 disc 2 m u l t i c o n t r o l 1 2 3 4 5 6 7 8 9 0 +10 & ^ 4 3:1 6 - select the disc select the desired track no. remaining time of disc ( total lights up) elapsed time of disc ( total lights up) remaining time of track being played elapsed time of track being played free datasheet http:///
xd-series (en) 22 basic section let's put out some sound 1. load a cassette tape. 2. select the deck to be used for playback. playback of tape 1 open the door. 2 insert a tape and close the door. press the play key of the desired direction. 3. start playback. to wind tape at high speed/to stop playback to stop playback selection of tape equalizer selection of dolby nr ? selection of reverse mode start playback ? when playing back a source which has been recording using the equalizer or 3d surround effect, select effect off with the sound control jog dial. i by loading a tape in the cassette deck to be used in playback beforehand, simply pressing the play key auto- matically turns the power on and starts playback. 0 push open 1 1 a b 2 2 & # # 3 3 a a r d s 1 1 2 2 1 1 3 3 free datasheet http:///
xd-series (en) 23 basic section selection of tape equalizer (main unit only) (xd-4....series only) ? the tape equalizer is effective for reduction of higher-frequency noise. select tape equalizer only when playing back a tape recorded with dolby noise reduction. (a tape recorded without dolby nr cannot be reproduced in normal au- dio if tape equalizer is selected when playing it.) lights up when tape equalizer is on. each press switches the modes as follows. 1 t. eq on ..... tape equalizer is used 2 t. eq off ....... tape equalizer is not used ? if the tape transport direction is opposite to the desired direction, press the play key corresponding to this. ? normal (type ), high (type ), or metal (type ) tape selection is set automatically. ? remove tape slack before loading. ? close the door securely. the indicators ( 2 , 3 ) indicate the current direction in which the tape advances when playback or record- ing is started automatically by the one-touch opera- tion function, etc. this direction is the direction stored in memory when the tape was last stopped. (to switch the tape transport direction, press the play key corresponding to the desired direction then press the stop ( & ) key.) transport direction indicators tape eq. tape direction indicators of currently selected deck. xd-4....series xd-5....series xd-4....series xd-5....series to wind tape at high speed ? press the & key to stop fast winding. each press switches the modes as follows. 1 .... playback stops after having played both sides of tape in a deck. (relay play : ) 2 ... endless playback of both sides of tape. 3 ...... playback stops after having played one side of tape. selection of reverse mode (main unit only) to fast wind in direction \ to fast wind in direction | 1 @& # rev. mode to stop playback ? do not take out the cassette tape until the tape transport has stopped completely. & # # reverse mode indication. lights up when a tape is present in the deck in use. displays the selected deck. let's put out some sound free datasheet http:///
xd-series (en) 24 basic section a tip for use of the tape counter the tape counter is set to 0000 when a cassette tape is loaded. by writing down the counter reading in case you want to interrupt recording (playback) in the middle of the tape, the memo will be helpful as a ref- erence for locating the same position when continu- ing the recording (playback) the next time. the tape counter figure decrements during recording or play- back of the back side (while the 2 tape transport in- dicator is lit). to set the tape counter to 0000, open the cassette holder once. then the counter will be reset. t0 ape 000 let's put out some sound relay play ? relay play is not possible in the reverse modes and . ? if a tape is loaded only in either deck, playback stops after having played both sides of the tape. when tapes are set in the decks a and b and the re- verse mode is set to (play of both sides), play of the second deck will be started automatically after play of the first deck has been completed. tape play will be repeated alternately. a a free datasheet http:///
xd-series (en) 25 basic section searching for the desired music program (dpss)(xd-5....series only) the dpss (direct program search system) is capable of detecting non-recorded spaces of more than 4 seconds as blanks between programs and, based on this information, can return to the beginning of the music program being played or the beginning of a desired program by skipping up to 16 other programs. the dpss may not function normally with the following kinds of tape. ? tapes containing several no-sound intervals of more than 4 seconds, such as conversation and talk tapes. ? tapes containing pianissimo sections, such as classical music tape. ? tapes in which large noise is recorded in blanks between programs. ? tapes containing blanks between programs that are shorter than 4 seconds. ? tapes recorded at low level. ? tapes recorded by cross-fade recording (in which the beginning of next program is overlapped on the end of previous program). notes notes to play the next program : press once. to play the 4th program after the current program : press 4 times. during play in direction 3 to play the next program : press once. to play the 4th program after the current program : press 4 times. to return to the beginningof the current program : press once. to play the 4th program before the current program : press 5 times. during play in direction 2 to return to the beginningof the current program : press once. to play the 4th program before the current program : press 5 times. let's put out some sound 1 @& # 1 @& # free datasheet http:///
xd-series (en) 26 basic section 1. select the broadcast band. receiving broadcast station collective presetting of stations one-by-one presetting each press changes the band. it is also possible to receive them by one-touch operations by storing up to 30 stations in the pre- set memory. 2. selecting the tuning mode when the band key is pressed, this unit will be switched on automatically. 4 1 tuning band tuning mode 1 1 1 fm 2 am or 1 fm 2 mw (am) 3 lw or 1 fm 2 mw (am) 3 sw ? the broadcast bands are variable depending on the model (country or area). when no stations have been memorized auto tuning : turn the multi control jog dial to receive the next tuned station automatically. (on the remote control unit, press the 1 or key.) manual tuning : turn the multi control jog dial to select a station. (on the remote control unit, press the 1 or key.) let's put out some sound r d s 3 3 1 1 2 2 m u l t i c o n t r o l 3 3 band 2 2 tuning mode 3. select a station. each press alternates the mode. auto (auto tuning) p.call (preset call) manual (manual tuning) ? when no operation has been performed for 5 seconds while p.call is displayed, the tuning mode is set automatically to auto . free datasheet http:///
xd-series (en) 27 basic section let's put out some sound ? when a key is held depressed, preset stations will be skipped at an interval of about 0.2 second. ? preset stations can also be recalled using the numeric keys of the remote control unit. band tuning mode collective presetting of stations (auto preset) keep the tuning mode key depressed (about 2 seconds). ? a maximum of 30 stations are preset automatically by giving the priority to the fm band. ? when there are many stations and the intended station has not been preset, please also use one-by-one presetting (manual preset) . ? the stations which have been preset are overwritten. for u.k., europe and russia other countries ? repeat steps 123 to preset other stations. ? if several stations are preset under the same number, the previous memory is replaced with the latest memory contents. one-by-one presetting (manual preset) 3 press the enter key again. presetting is cancelled when no operation is ex- ecuted for 5 seconds or more. 2 select one of the preset numbers from 1 to 30. presetting is cancelled when no operation is ex- ecuted for 5 seconds or more. 1 press the enter key during reception. m u l t i c o n t r o l enter -0 -fm 89.0 enter frequency display lights during auto tuning the indicator lights when a station is received lights during stereo reception 00 3fm 89.0 -0 -fm 89.0 example when an fm station is received ? some stations may not be able to be preset if their reception conditions are weak. ? use the manual tuning mode when reception is noisy due to weak reception. (in the manual mode, stereo broadcasts are received in monaural.) ? normally, use the auto (auto tuning) mode. ? if you are operating the remote control unit, the auto (auto tuning) and manual tuning mode can be alternated by pressing the stop ( 7 ) key. a. uto memo when stations have been memorized (preset call) turn the multi control jog dial to select a station. (on the remote control unit, press the 4 or key.) a .preset free datasheet http:///
xd-series (en) 28 basic section 1. load a cassette tape. (recording is available on deck b only.) 2. select the tape transport direction. let's record recording on tape 1 open the door of deck b. 2 insert a tape. 3 close the door. 1 select deck b by pressing the a/b key. 2 press the play key correspond- ing to the desired direction. 3 stop playback (by pressing the & key). to reverse the transport direction ? when recording is started, the tape is transported in the direction selected in this step. ? wind the tape to the position where recording is to be started. check the tape transport direction indicator. 3. set the recording condition. 1 select the reverse mode. ? 2 select the dolby nr mode. (xd-5...series only) ? 0 push open 1 1 a & # # 2 2 ? the tape equalizer cannot be used in recording. (xd-4...series only) when equalizer or another effect is applied to the sound, the sound with the applied effect can be recorded. i note that this cassette deck cannot record onto metal tapes. note note note rev. mode dolby nr 3 3 ? differentiation between normal (type ) and high (type ) tape is set automatically. ? remove tape slack before load- ing. r d s 1 1 5 5 3 3 4 4 2 2 free datasheet http:///
xd-series (en) 29 basic section 4. select the source to be recorded. 1 tuner (radio) 2 cd 3 tape (this source cannot be recorded.) 4 md/dvd (external input) ( input level adjustment u ) the input source component to be recorded should be displayed. ? if a disc has already been loaded when the cd input is selected, it will starts to play automatically. in this case, press the stop ( & ) key to stop it. select an input source other than tape . 1 start recording. 2 play (or tune) the input source to be recorded. 5. start recording. ? even if deck a is selected, it is automatically switched to deck b at the start of recording. ? recording stops automatically when the tape side(s) to be re- corded have been fully recorded. ? press the stop ( & ) key of the cas- sette deck unit to stop recording. c2 d01 1:1 lights input 4 4 rec/arm 5 5 xd-4....series xd-5....series let's record the dolby nr system minimizes the hiss noise heard when playing tape. when playing a tape prerecorded with dolby nr on, be sure to set the dolby nr on for playback. selection of dolby nr (noise reduction) (main unit only) (xd-5....series only) lit when dolby nr is on. dolby nr to pause recording (main unit only) ? pressing the key pauses recording after leaving a non-recorded space of about 4 seconds. ? if the key is pressed again in less than 4 seconds after it has been pressed, recording resumes from that instant. each press switches the modes as follows. 1 .... recording stops after having re- corded both sides of tape. 2 ... recording stops after having re- corded both sides of tape. 3 ..... recording stops after having re- corded one side of tape. selection of the reverse mode (main unit only) rec/arm rev. mode lights ? select the dolby nr mode according to the recording condition of the tape. each press switches the modes as follows. 1 1 nr on .... dolby nr is used. 2 1 nr off ... dolby nr is not used. dolby noise reduction manufactured under license from dolby laboratories. dolby and the double-d symbol are trademarks of dolby laboratories. xd-4....series xd-5....series ? when the 2 transport direction indicator is lit, recording always stops after having recorded one side of tape. free datasheet http:///
xd-series (en) 30 basic section points in cd recording when recording cd tracks onto a tape, if you leave the cassette deck in record-pause mode beforehand, the cassette deck recording can be started at the same time as the cd starts to be played. (synchro record- ing function) 1 put the cd player in pause mode. 2 select the track to be recorded with the skip ( 4 , ) keys. (the cd player pauses at the beginning of the selected track.) 3 put the cassette deck in record-pause mode. (press the rec/arm key twice.) 4 start playing the cd. (synchro recording starts.) ? recording stops when the stop ( & ) key of the cd player is pressed. let's record there may be cases in which beat noise interferes with recording of lw broadcasting. in such a case, press the a/b key during recording to reduce or suppress the beat noise. beat cancel function (for russia) a b free datasheet http:///
xd-series (en) 31 basic section copying tape (tape dubbing) 1 select the tape input. 2 press the stop key. 3 select (double-side recording) or (one-side recording). 4 select tape dubbing. the contents of the tape in deck a can be copied onto the tape in deck b. ? dubbing ends automatically when the side(s) to be dubbed has been completed. playing tape recording tape load tapes in the decks. + scrolled display (tape dubbing) 5 use the same tape transport directions. 6 start dubbing. (1) select the transport direction of deck a. (2) select the transport direction of deck b. ? when recording is started, the tape will be transported in the direction selected in this step. ( > :side a, < : side b) + scrolled display (deck a play direction) + scrolled display (deck b record direction) + scrolled display (press 'enter' to start) ti ape dubb lights pt ress 'en input rev. mode enter to stop dubbing ? the deck b will stop after creating a non-recorded portion of about 4 sec, and then the deck a will stop. ? dubbing can also be stopped by pressing the stop ( & ) key of the cassette deck unit. note that the non- recorded space is not created in this case. the dolby nr or tape eq. key is ineffective during dubbing. the tape recorded on deck b assumes the same dolby nr condition as the tape played on deck a. rec/arm menu select m u l t i c o n t r o l & # # let's record the following items can be selected by turning the multi control jog dial. recording options tape dubbing audio options clock options select m u l t i c o n t r o l select m u l t i c o n t r o l a a da eck a pl a deck > dc eck b re b deck > free datasheet http:///
xd-series (en) 32 application section listening in the desired sequence (program playback) playback of cd any titles on the discs in the tray can be listened to in the desired sequence. (max. 32 titles) select the cd input. 1 check that the cd player is in the stop mode. 2 select cd program play. 3 enter track no.s in the order you want to play them. 1 select the disc. 2 select the track. 3 press the enter key. (to select other tracks, repeat steps 1 and 2 for each of the additional tracks.) ? if the operation in step 2 is performed during playback of a track, the current track can be programmed as the first track in the program. + scrolled display (select disc/track no.) ? even if you program a disc or track which does not exit in the tray, it is deleted automatically in playback. ? press the back key to return to the previous step and restart operation from there. ? up to 32 tracks can be programmed. when full is displayed, no more tracks can be programmed. + scrolled display (press 'enter' to start, 'jog' to check ) menu select m u l t i c o n t r o l select m u l t i c o n t r o l & ^ select m u l t i c o n t r o l enter ss elect di p? 01 d1 t? p1 01 d1 t0 pt ress 'en + scrolled display (cd program play) cm d progra lights the following items can be selected by turning the multi control jog dial. cd program play (recording options) audio options clock options if it is in play mode lights (go to step 5 if you do not need to check the program contents.) free datasheet http:///
xd-series (en) application section 33 playback of cd 1 select cd program play. 2 press the menu key. 4 check the programmed tracks (and replace, add or delete tracks as required). to check: ? the blinking item can be replaced. to replace a track in the program: ? the added track number is added to the end of the existing program. ? the programmed tracks are displayed in sequence. ? turn the multi control jog dial during program playback to stop to the previous or next programmed track. ? when the jog dial is rotated a little in the direction of counterclockwise once during playback, the track being played will be played from the beginning. ? to check (modify, add or delete) the programmed tracks after playback, perform the operations in steps 2 and 4 . 5 enter it. ? if the key is pressed during playback, normal playback in order of tracks resumes from the current track. ? the program mode can also be canceled by pressing the 0 open key. 1 select the programmed disc or track to be replaced and press the select key. 2 select a disc or track to re- place the disc or track selected above (step 3 - 1 and 2 ). 1 select the display as shown on the right and press the select key. 2 perform the same operations as in step 3 - 1 and 2 . to add a track to the program: to delete a track from the program: 1 select the programmed disc or track to be cleared and press the select key. 2 select clear and press the select key. goes off m u l t i c o n t r o l enter select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l to quit the program mode menu p2 01 d1 t0 p4 12 d3 t0 p4 12 d3 t0 p? 13 d? t? p4 12 d3 t0 p12 clear display when 12 tracks have been programmed menu select m u l t i c o n t r o l press the time key on the remote control unit to switch the time display. (playback starts from the first programmed track (program no. 1)) free datasheet http:///
xd-series (en) 34 application section select the cd input. repeated playback desired titles or discs can be played back repeatedly. playback of cd disc skip 1 cancel pgm. 2 select the disc. 3 select the track. 4 select one track repeat. to repeat only one track 1 2 3 4 5 6 7 8 9 0 +10 repeat if the pgm indicator is lit, make sure to turn it off. goes off lights xd-4....series xd-5....series (remote control unit) (remote control unit only) to repeat a disc 1 cancel pgm. 2 select the disc. 3 select disc repeat. disc skip repeat if the pgm indicator is lit, make sure to turn it off. (remote control unit only) press the key repeatedly to switch the display. 1 repeat off (repeat canceled) 2 one track repeat 3 disc repeat 4 all repeat + scrolled display (one track repeat) ack r one t goes off lights press the key repeatedly to switch the display. 1 repeat off (repeat canceled) 2 one track repeat 3 disc repeat 4 all repeat xd-4....series xd-5....series + scrolled display(disc repeat) da isc repe to stop repeated playback press the repeat key repeatedly until the repeat mode is switched off. ? the repeat mode can also be canceled by pressing the 0 open key. m u l t i c o n t r o l (main unit) free datasheet http:///
xd-series (en) application section 35 playback of cd to repeat all discs 1 cancel pgm. 2 select the disc to be played first. 3 select all repeat. disc skip if the pgm indicator is lit, make sure to turn it off. goes off repeat to stop repeated playback press the repeat key repeatedly until the repeat mode is switched off. ? the repeat mode can also be canceled by pressing the 0 open key. lights xd-4....series xd-5....series (remote control unit only) press the key repeatedly to switch the display. 1 repeat off(repeat canceled) 2 one track repeat 3 disc repeat 4 all repeat + scrolled display (all repeat) at ll repea repeat to repeat only the programmed tracks 1 perform the procedure in listening in the desired sequence (program playback) till step 3 to program the desired cd tracks. ? 2 start playback. 3 select pgm repeat (remote control unit only) enter ? all of the programmed tracks will be played repeatedly. pt gm repea xd-4....series xd-5....series press the key repeatedly to switch the display. 1 pgm repeat 2 repeat off (repeat canceled) + scrolled display (pgm repeat) lights lights free datasheet http:///
xd-series (en) 36 application section playback of cd random random playback select the ?d?input. press the key repeatedly to switch the display. 1 one disc random random play of one disc 2 all disc random random play of all discs 3 random off (normal playback) as the titles each time are selected randomly, the music can be enjoyed without getting tired of it. random playback can play tracks in one to three discs. 1 cancel pgm. 2 select the random mode. (for one disc random playback, select the disc in advance.) random play of all discs random play of one disc + scrolled display (one disc random) ? the displayed character information returned to normal display and normal playback in order of track numbers starts from the track being played. to cancel random playback select random off. random to select another track in the middle of playing one to repeat random playback select random repeat. repeat ? pressing the 4 key once returns to the beginning of the track being played. ? playback stops after each title has been played once. ? when the time key of the remote control unit is pressed during playback, the time display appears but it soon returns to the original display. + scrolled display (all disc random) 4 d rndm t15 or ne disc each press switches the modes as follows. 1 random repeat ..... random repeat mode 2 repeat off .............. repeat canceled if the pgm indicator is lit, make sure to turn it off. goes off (remote control unit only) (remote control unit only) (remote control unit only) a rndm t12 ar ll disc free datasheet http:///
xd-series (en) application section 37 rds is a system which transmits useful informa- tion (digital data) for fm broadcasts together with the broadcast signal. tuners and receivers designed for rds reception can extract the in- formation from the broadcast signal for use with various functions such as automatic display of the station name. r.d.s. (radio data system) (for u.k., europe and russia) this unit is equipped with the following functions utilizing rds data: pty (program type identification) search : ? the tuner automatically searches for a station which is currently broadcasting a specified program type (genre). ps (program service name) display : (see below.) when an rds broadcast is received, the station name is automatically displayed. eon (enhanced other network) : a when the information to be received is set in advance and any rds station in the same network starts broadcasting of such information, the reception automatically will be switched to that station. the rds indicator lights up when an rds broadcast (signal) is received. ? some functions may not be provided or be given differ- ent names depending on countries or areas. pressing the rds disp. key changes the dis- play contents. display mode priority ranking when an rds broadcast is received : 1 ps (program service name) display : when an rds broadcast is received, the station name is automatically displayed. if no ps data was sent, no ps is displayed. 2 frequency display : the frequency of the current station is displayed. note before the use of rds set the receiving band to fm and preset rds stations with the auto preset function. | to switch the display contents rds disp. rds tp pty eon ta news b bc 00 1fm102.5 for reception of rds stations, the auto presetting function must be used to preset the stations. with the auto presetting function, rds stations are preset with priority. (remote control unit only) free datasheet http:///
xd-series (en) 38 application section a to select using the 4 keys the 4 keys can be used to select one of the 29 program types by displaying them in sequence. press and hold the key and release it when the desired program type appears. b to select using the numeric keys the numeric keys can be used to specify the desired program type directly by selecting a number between 01 and 28. example: to select 23: press 003 . program type name r.d.s. by specifying the type of program (genre) you want to listen to, the tuner automatically searches for a station which is currently broad- casting a program of the specified type. searching for a desired program type (pty search) set the reception band to fm. preset rds stations with the auto preset function. | when an rds broadcast is received, the program type is shown on the display. if no pty data is available, or if the station is not an rds station, none is displayed. program type table select while pty is lit. 4 1 2 3 4 5 6 7 8 9 0 +10 n 0 ews 102.5 tp pty eon ta news rds pop m rock m easy m light m classics other m news affairs info sport educate drama culture science varied weather finance children social religion phone in travel leisure jazz country nation m oldies folk m document 01 02 03 04 05 06 07 08 09 00 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 a 4 keys b display 4 down up pop music rock music easy listening music light classical serious classical other music news current affairs information sport education drama culture science varied weather finance childrens program social affairs religion phone in tr ave l leisure jazz music conutry music national music oldies music folk music documentary 1 select the pty search mode. 2 select the desired program type. use program type table on the right for your convenience. (remote control unit only) (remote control unit only) pty free datasheet http:///
xd-series (en) application section 39 repeat steps 1 , 2 , 3 . when searching for a rock music broadcast when a station is received. to change to a different program type : display while the tuner is searching. blinks goes off ? no sound is heard while pty is blinking. ? if a program of the desired type cannot be found, no prog is displayed, then after several sec- onds the display returns to the original display. ? if a program of the desired type is found, that program is received and the program type name display changes temporarily to the frequency display, and then to the station name display. station name display. program type name display. (press the key again during search to cancel it.) 3 start the search. pty r 0 ock 1 m 2.5 tp pty eon ta news rds r.d.s. (remote control unit only) b 0 bc 102.5 tp pty eon ta news rds free datasheet http:///
xd-series (en) 40 application section r.d.s. to be able to listen to the desired information at any time (eon) by using the eon function, which manages the information of other stations, listening to desired infor- mation like traffic information or news etc. can be reserved even when it is not being transmitted at the present. when listening to a station with the eondisplay lit and another station of the same network starts to broadcast an information program for which a reservation has been made, then that station will be selected automatically. when the desired information program ends, return is made to the original program. each press switches the modes as follows. 1 ta ........................ traffic announcement 2 news .................. news 3 ta/news ............ traffic announcement/ news 4 display not lit ...... eon cancelled 1 auto preset the stations. 2 select the desired information. 3 receive an rds station. (the eon data presently being broadcasted are taken in automatically.) this is not required when auto presetting has already been executed. | ? when all 30 stations have already been preset by the procedure for one-by-one presetting (manual preset) , the eon function will not operate. auto presetting must be used. 1 receive a broadcast. 2 keep the tuning mode key pressed (2 sec or longer). rds and eon are lit select a station where rds and eon are lit. ? please execute automatic presetting when ta and news can not be selected. lights when news is selected lights with a station broadcasting traffic an- nouncement programs. ? when eon does not light although an rds station is received, that station is not transmitting eon data. please select a different station. ? if you want ta programs, select the stations with which the tp indicator lights. set the reception band to fm. band tuning mode 00 1fm102.5 tp pty eon ta news rds ta/news 4 00 2fm 90.0 tp pty eon ta news rds (remote control unit only) free datasheet http:///
xd-series (en) application section 41 ? when one of the stations of the network of the station received in 3 starts broadcasting the program contents selected in 2 , that station will be received automatically. at this time, tape playback will stop and cd playback will pause. however, external equipment (md/dvd) will remain as it is. ? the eon function does not operate during recording (including dubbing). ? when the transmission of the selected program contents ends in case of automatic reception with the eon func- tion, return will be made to the status directly before operation of the eon function. when tape or cd play- back has been interrupted, it will be continued from the point of interruption. cd or tape playback may also be started. as long as the unit is on, the unit is always ready for the reception. waiting for information while a rds station without eon function is tuned if the eon indicator does not light with the rds station in steps 3 and 4 , the tuner will wait for only the desired information broadcast from the tuned rds station pro- vided that the desired information has been selected in the previous step. tp (traffic program) indicator the lighting of the tp indicator indicates that the cur- rently tuned station or a station in the same network as it broadcasts traffic announcement programs. if the tp indicator already lights with the current station, you can listen to the traffic announcement program through the station without making reservation with the eon func- tion. 4 wait for the desired information. r.d.s. free datasheet http:///
xd-series (en) 42 application section selection of the recording type with this unit, the following edit recording is possible according to the purpose. convenient cd recording note that this cassette deck cannot record onto metal tapes. recording only desired titles e perform this operation when a track you want to record starts during cd playback. this starts recording of the track from the beginning. \ cd one track recording if you want to select the track to be recorded while playing a cd recording of an entire cd r perform the cd direct recording operation while the cd player is in stop mode to start recording. \ cd direct recording if you want to record a cd in order of track numbers recording the programmed titles t program the desired tracks from up to 3 cd discs in the desired order and record the programmed playback onto tape. \ cd program recording if you want to record only the desired tracks note note note with recording onto tape, the track will be interrupted for the part of the guide tape at the tape reversal, where recording is not possible. please use single-side recording if this is to be avoided. note note note in regard to cd-text (remote control unit only) when a cd-text disc is played on this unit, it dis- plays the text information (disc or track title) re- corded in the cd. to switch the displayed text information between the disc title and track title during playback, press the text disp. key. scrolls the disc title display. cd players time display. scrolls the track title display. wi orld mus nb ew york: text disp. (when pressed during playback) c2 d01 1:1 free datasheet http:///
xd-series (en) application section 43 recording preparations are required. (steps 1 to 3) at the time of cd playback, any desired title can be selected immediately for recording. 1 playback of cd. 2 select recording options. 3 select cd one track recording . 4 start recording. to end recording in the middle recording only desired titles (cd one track recording) when equalizer or another effect is applied to the sound, the sound with the applied effect can be recorded. i convenient cd recording ? select a mode other than random play. ? playback restarts from the beginning of the track being played and recording starts at the same time. + scrolled display (cd one track recording) the following items can be selected by turning the multi control jog dial. cd one track recording (only during cd playback) cd direct recording cd program recording timer recording ? both the cassette deck and cd player stop. + scrolled display (press 'enter' to start) + scrolled display (recording options) lights & ^ select m u l t i c o n t r o l enter & ^ r ecording ca d one tr pt ress 'en the following items can be selected by turning the multi control jog dial. cd program play recording options audio options clock options when recording has been completed, a non-recorded portion of 4 seconds will be produced and the cassette deck part will stop. the cd player will enter tempo- rary stop condition. to record a different track, repeat the steps 1 to 4 . menu select m u l t i c o n t r o l free datasheet http:///
xd-series (en) 44 application section recording preparations are required. (steps 1 to 4) 1 check that the cd player is in the stop mode. 2 select recording options. 3 select cd direct recording. 4 select the disc. 5 start recording. recording of an entire cd (cd direct recording) perform the following operation while the cd player is in stop mode to start recording at the same time as the start of playback. when equalizer or another effect is applied to the sound, the sound with the applied effect can be recorded. i convenient cd recording ? recording of cd starts at the same time as playback. ? at the end of tape, the music is not recorded on the leader tape portion. if you do not want any music to be interrupted in the middle, refer to recording on tape and start recording of side b with the interrupted track. to end recording in the middle ? both the cassette deck and cd player stop. + scrolled display (cd direct recording) + scrolled display (select disc no.) + scrolled display (press 'enter' to start) select m u l t i c o n t r o l select m u l t i c o n t r o l enter & ^ c d direct d isc no.1 ss elect di pt ress 'en + scrolled display (recording options) lights r ecording the following items can be selected by turning the multi control jog dial. cd program play recording options audio options clock options menu select m u l t i c o n t r o l the following items can be selected by turning the multi control jog dial. cd direct recording cd program recording timer recording & ^ if it is in play mode free datasheet http:///
xd-series (en) application section 45 recording preparations are required. (steps 1 to 4) recording the programmed titles (cd program recording) program the desired tracks from up to 3 cd discs in the desired order and record the programmed playback onto tape. convenient cd recording when equalizer or another effect is applied to the sound, the sound with the applied effect can be recorded. i + scrolled display (cd program recording) to end recording in the middle ? both the cassette deck and cd player stop. + scrolled display (press 'enter' to start, 'jog' to check) select m u l t i c o n t r o l enter cm d progra & ^ pt ress 'en ? the program mode is maintained even after completion of recording. to return to the normal mode, it is required to cancel the program mode. + scrolled display (recording options) lights r ecording the following items can be selected by turning the multi control jog dial. cd program play recording options audio options clock options & ^ menu select m u l t i c o n t r o l 1 check that the cd player is in the stop mode. 2 select recording options . 3 select cd program recording. 4 program the desired tracks. 5 start recording. 1 select tracks in the order you want to play them. (perform step 3 on page 32.) 2 check, replace, add or delete the pro- grammed tracks as required. (perform step 4 on page 33.) the following items can be selected by turning the multi control jog dial. cd direct recording cd program recording timer recording if it is in play mode lights free datasheet http:///
xd-series (en) 46 application section this unit permits selection of the levels of the equalizer and sound field reproduction effects. please select the equalizer as desired according to the music genre. select the sound field mode ac- cording to the desired atmosphere. effective sound adjustment 1 select audio options. 2 select balance. 3 adjust. the left volume is decreased. the right volume is decreased. the following items can be selected by turning the multi control jog dial. custom eq 1 custom eq 2 custom eq 3 balance md/dvd input level ( only when the md/dvd input is selected ) indicates the balance setting + scrolled display ( balance) + scrolled display ( adjust l/r balance) adjusts the balance of left and right volume. balance adjustment select m u l t i c o n t r o l + scrolled display (audio options) ai udio opt b alance ar djust l/ l --- ---r indicates the center the following items can be selected by turning the multi control jog dial. (cd program play) (recording options) (tape dubbing) audio options clock options enter m u l t i c o n t r o l lights menu select m u l t i c o n t r o l free datasheet http:///
xd-series (en) application section 47 the input level from an external component connected to the md/dvd input jacks, such as a md recorder, dvd player, vcr or analog turntable can be adjusted as desired. adjust so that the volume of the md/dvd input source sounds at an equivalent level to the cd . input level adjustment 1 select the md/dvd input. 2 select audio options. 3 select md/dvd input level . 4 adjust the following items can be selected by turning the multi control jog dial. custom eq 1 custom eq 2 custom eq 3 balance md/dvd input level + scrolled display (md/dvd input leve) + scrolled display (adjust level) ? adjustment is possible in the range from 0 to -- 7 . input mp d/dvd in av djust le l evel -2 effective sound adjustment select m u l t i c o n t r o l enter m u l t i c o n t r o l + scrolled display (audio options) ai udio opt the following items can be selected by turning the multi control jog dial. (recording options) audio options clock options lights the level is increased. the level is decreased. menu select m u l t i c o n t r o l free datasheet http:///
xd-series (en) 48 application section selecting the equalizer pattern and 3d surround level select the desired pattern and 3d surround level according to the category of the played music. the equalizer and 3d surround effects can be recorded together with the music. listening to music with desired tone and sound field/ switching the display (equalizer effect and 3d surround effect) this unit permits selection of six preset equalizer patterns and three users equalizer patterns as well as the 3d surround levels. the s.direct (source direct) mode allows you to reproduce pure sound by bypassing the ex.bass, equalizer and 3d surround circuitry. 1 play desired music. 2 select the desired equalizer pattern. effective sound adjustment 3d surround this is a system producing a three-dimensional sound space. the feeling of depth, the width of the sound field, etc. are improved clearly, and the listening area also is widened. ? to cancel the equalizer, 3d surround and s.direct , select effect off . switching the sound level meter display mode each press switches the modes as follows. display auto display 1 display 2 display 3 ? when display auto is selected, the display mode during cd playback changes to display 1 , display 2 and display 3 every time the track changes. ? display 3 is displayed regardless of the current music signal. lights when s.direct is selected. lights when equalizer is selected. lights when 3d surround is se- lected. s o u n d c o n t r o l ? the equalizer pattern and 3d surround level cannot be switched on/off or controlled in the middle of recording. sound control or equalizer patterns and 3d surround levels that can be recalled rock .................. rock music disco ................. disco music pop .................... pop music movie ................ movie music jazz ................... jazz music classic ............... classic music custom eq 1 custom eq 2 custom eq 3 3d level 1 ......... 3d surround level 1 3d level 2 ......... 3d surround level 2 s. direct ............. pure sound can be reproduced by bypassing the ex.bass, equalizer and 3d surround cir- cuitry effect off ............ normal playback equalizers manual memory created by the user display /demo free datasheet http:///
xd-series (en) application section 49 creation and memorizing of an equalizer pattern you can edit desired patterns manually and store them in memory. effective sound adjustment the following items can be selected by turning the multi control jog dial. custom eq 1 custom eq 2 custom eq 3 balance md/dvd input level ( only when the md/dvd input is selected ) the following items can be selected by turning the multi control jog dial. 3d lev. off .... 3d surround off 3d lev. 1 ...... 3d surround level 1 3d lev. 2 ...... 3d surround level 2 1 select audio options. 2 select the number to be used for storage. (custom eq1 ~ eq3) 3 adjust the equalizer pattern. 4 establish the 3d surround level. + scrolled display (adjust bass) ? each frequency band can be adjusted in the range be- tween -- 8 and + 8 . ? the bass , mids and highs frequency bands can be adjusted independently by repeating step 3 for each of them. as djust ba bass -8 3d lev. 1 the following items can be selected by turning the multi control jog dial. (cd program play) (recording options) (tape dubbing) audio options clock options to decrease the level to increase the level + scrolled display (audio options) ai udio opt lights menu select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l enter m u l t i c o n t r o l free datasheet http:///
xd-series (en) 50 application section this unit incorporates a clock function. be sure to adjust the correct time before using the timer func- tion. the time is displayed only while the power is off. 1 select clock options. 2 select adjust time. 3 enter the figure of hour. 4 enter the figure of minute. clock adjustment ? the time display starts to blink. ? press the select key. the hour is entered and the minute display starts to blink. example: adjustment to 8:45 the following items can be selected by turning the multi control jog dial. sleep time adjust time o.t.t. timer play auto power save to decrease the figure to increase the figure other countries am12 ? am1 ? am2... pm1 ? pm2... ? am12 ... 00 ? 01 ? 02...59 ? 00 ? 01... ? press the back key to return to the previous step and restart operation from there. ? to adjust correct time, press the enter key at the same moment as a time announcement. to decrease the figure to increase the figure + scrolled display ( clock options) lights (in standby mode) ? when the key is pressed while the timer indicator is lit, the timer setup mode is displayed after the clock display. ? the clock display blinks after the power cord has been unplugged from the ac power outlet and plugged in again or after a power failure. in this case, set the time of the day again. select (displayed for approx. 5 sec.) ci lock opt the following items can be selected by turning the multi control jog dial. (cd program play) (recording options) (tape dubbing) audio options clock options adjust the clock before setting the timer. m 8:00a m 8:45a for u.k., europe and russia 0 ? 1 ? 2...13 ? 14... ? 0 ... 0 8:0 5 8:4 other countries for u.k., europe and russia to display the time menu select m u l t i c o n t r o l select m u l t i c o n t r o l enter m u l t i c o n t r o l select m u l t i c o n t r o l free datasheet http:///
xd-series (en) application section 51 adjust the clock before setting the timer. p timer operation sleep timer (sleep) the power is turned off automatically after the specified period has elapsed. operate easy to use timer (o.t.t.) playback of the selected input source starts at the specified time, and the power is switched off after one hour. this timer operates only once directly after setting. timer programming timer playback : plays (or receives) the selected source in the set time range. ai timer playback (when timer playback starts, the volume increases gradually.) timer recording : records the selected source in the set time range. auto power save when the power is on and neither recording nor playback is executed for 30 minutes or more, the power is switched off automatically by this function. sleep timer (sleep) set the number of minutes after which the power is to be turned off. 1 select clock options. 2 select sleep timer. 3 set the time 10 ? 20 ? 30...80 ? 90 ? sleep off ? 10 ? 20... ? the displayed time changes in 10-minute steps. the maxi- mum time that can be set is 90 minutes. ? the power is turned off automatically after the set time has elapsed. ? to cancel the sleep timer, turn the power off or select sleep off . ? the sleep timer does not operate until o.t.t. operation or program timer operation has ended. lights s leep 90 blinks the following items can be selected by turning the multi control jog dial. sleep time adjust time o.t.t. timer play auto power save adjust the clock before setting the timer. + scrolled display ( clock options) lights ci lock opt the following items can be selected by turning the multi control jog dial. (cd program play) (recording options) (tape dubbing) audio options clock options menu select m u l t i c o n t r o l select m u l t i c o n t r o l enter m u l t i c o n t r o l free datasheet http:///
xd-series (en) 52 application section ? the on time can be set in steps of 5 minutes. 1 select the desired source and adjust the volume. 2 select clock options . 3 select o.t.t.. 4 select o.t.t. on. 5 enter the on time 6 put the unit in standby mode. the program timer does not operate until o.t.t. operation has ended. operate easy to use timer (o.t.t.) timer playback can be set with a simple operation of just setting the time. with this function, the last source selected before turning power off can be played by the timer. the power turned on by the timer is switched off automatically in an hour after the timer playback starts. the following items can be selected by turning the multi control jog dial. sleep time adjust time o.t.t. timer play auto power save timer operation the following items can be selected by turning the multi control jog dial. o.t.t. off ( canceled) o.t.t. on ? to cancel the o.t.t. timer, select o.t.t. off . timer standby lights + scrolled display ( set on time) + scrolled display ( clock options) lights ci lock opt the following items can be selected by turning the multi control jog dial. (cd program play) (recording options) (tape dubbing) audio options clock options m 7:20a sm et on ti 7:20 the time is advanced. the time is returned for u.k., europe and russia other countries adjust the clock before setting the timer. adjust the clock before setting the timer. p lights ? if the timer indicator is blinking now, set the time of the day again. p menu select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l enter m u l t i c o n t r o l on/standby on/standby power or free datasheet http:///
xd-series (en) application section 53 timer programming 1 make preparations for the play (recording). ? when the timer function is used for timer recording of an input source, the speakers do not output the audio even after the unit is turned on by the timer. playing or recording the auxiliary input source make preparations for record- ing. make timer setting of the component connected to the md/dvd input jacks. for timer playback or ai timer playback for timer recording 1 select clock options. 1 select recording options. 2 select timer play. 2 select timer recording. 3 select the timer operation. 2 adjust the listening volume. continued on next page... the station should be preset prior to the above. | insert a disc. (program playback is not possible.) select the disc to be played (1, 2 or 3). ) set a tape in the deck you want to play back the tape. a to listen to radio to listen to cd to listen to tape select m u l t i c o n t r o l for recording the program timer can set timer playback and timer recording and both of these functions can be reserved concurrently. either everyday (executing a timer program once every day) or one time (executing it only once) can be selected for each timer program. once the time range and content of a timer program has been set, it can be activated or deactivated as desired. ? if you made a mistake during timer setting: press the back key to return to the previous step and restart operation from there. adjust the clock before setting the timer. timer operation adjust the clock before setting the timer. p select m u l t i c o n t r o l (cd program play) (recording options) (tape dubbing) audio options clock options (cd program play) recording options (tape dubbing) audio options clock options sleep timer adjust time o.t.t. timer play auto power save cd one track recording (only when the cd input is selected and during playback) cd direct recording (only when the cd input is selected) cd program recording (only when the cd input is selected) timer recording select menu m u l t i c o n t r o l select menu m u l t i c o n t r o l lights lights free datasheet http:///
xd-series (en) 54 application section 4 select everyday or one time. ? to cancel a timer operation, select timer off under timer play (in case of timer playback) or timer recording (in case of timer recording). the following items can be selected by turning the multi control jog dial. timer off ( canceled) everyday one time 5 enter the on time. 6 enter the off time. + scrolled display (select on time) + scrolled display (select off time) ? after entering the hour, enter the minute with the same procedure. ? after entering the hour, enter the minute with the same procedure. ? reserve the timer recording program and timer playback program by leaving an interval of 1 minute or more so that their time ranges do not overlap. the reservation contents cannot be cleared. the contents are cleared only when they are changed. on sn elect o :0 am 0 7: 0 0 on 7 sf elect of off 8:0 am 0 off 8: 0 0 the time is advanced. the time is returned. the time is advanced. the time is returned. adjust the clock before setting the timer. timer operation auto power save when the power is on and neither recording nor playback is executed for 30 minutes or more, the power is switched off automatically by this function. 1 select clock options. 2 select auto power save. 3 select a.p.s. on or a.p.s. off. ? the auto power save operation does not occur unless the o.t.t. or program timer operation has completed. ? when the tuner or md/dvd input is selected, this function operates only when the volume is set to zero. a.p.s. off auto power save is not used. a.p.s. on auto power save is used. (cd program play) (recording options) (tape dubbing) audio options clock options sleep timer adjust time o.t.t. timer play auto power save select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l enter m u l t i c o n t r o l select menu m u l t i c o n t r o l free datasheet http:///
xd-series (en) application section 55 for timer recording 1 select the input source. select the recorded input source. 2 select the broadcast station (only when tuner is selected above). select the preset station no. select m u l t i c o n t r o l + scrolled display (press 'enter' to save) pt ress 'en 8 press the enter key. 9 put the unit in standby mode. ? the set program content items are displayed one after another. ( everyday or one time = on time = off time = mode = input source = preset channel) lights enter timer standby select m u l t i c o n t r o l adjust the clock before setting the timer. timer operation 7 make the desired reservation. 1 tuner ...... radio 2 md/dvd ... external input for timer playback or ai timer playback 1 select the mode. select play or ai play. 2 select the input source. select the source to be played. 3 select the broadcast station (only when tuner is selected above). select the preset station no. select m u l t i c o n t r o l select m u l t i c o n t r o l select m u l t i c o n t r o l 1 play ..... timer play 2 ai play .. timer play with gradually increas- ing volume 1 tuner ....... radio 2 cd 3 tape 4 md/dvd .... external input ? if the timer indicator is blinking now, set the time of the day again. p 00 3fm 89.0 00 3fm 89.0 on/standby on/standby power or free datasheet http:///
xd-series (en) 56 knowledge section maintenance cotton swab tape guides pinch roller head capstan cleaning the head section there are precisely aligned parts around the heads, including the tape guides. when cleaning, pay special attention so as not to apply shock to them. cleaning the heads and peripheral components for maintaining the best condition of the deck and for longer service life, always keep the heads (recording / playback / erase), capstan and pinch roller clean. to clean them, perform the following: 1. open the cassette holder. 2. using a cotton swab dipped in alcohol, clean the head (recording / playback / erase), capstan and pinch roller carefully. demagnetizing the head when the recording / playback head is magnetized, the sound quality will deteriorate. in such a case, demagnetize the head using a commercially available demagnetizer (head eraser). reference note note note maintenance of the unit when the front panel or case becomes dirty, wipe with a soft, dry cloth. do not use thinner, benzine, alcohol, etc. for these agents may cause discoloration. in regard to contact cleaner do not use contact cleaners because it could cause a mal- function. be specially careful not to use contact cleaners containing oil, for they may deform the plastic component. stored contents which are cleared immediately when power plug is unplugged from power outlet clock display stored contents which are cleared in at least a day after power plug is unplugged from power outlet amplifier power status (on or off) input selection volume control value balance level equalizers manual memory created by the user 3d surround level tuner unit receiving band frequency preset stations program timer setting con- tents cassette deck unit transport direction dolby nr tape equalizer reverse mode memory backup function note related to transportation and movement before transporting or moving this unit, carry out the following operations. 1 turn the power on but do not load a disc. 2 press the 6 key. 3 wait a few seconds, and ensure that the display is as shown below. 4 wait for a few seconds then turn power off. cc dno dis important items caution on condensation condensation (of dew) may occur inside the unit when there is a great difference in temperature between this unit and the outside. this unit may not function properly if condensation oc- curs. in this case, leave the unit for a few hours with the power left on, and restart the operation after the con- densation has dride up. be specially cautious against condensatin in a fol- lowing circumsatance: when this unit is carried from a place to another across a large difference in temperature, when the humidity in the room where this unit is installed increases, etc. in most cases it is an infringement of copyright to make copies of tapes or discs without the permission of the copyright owners. anyone wishing to copy commercially available tapes or disc should contact the mechanical copy- right protection society limited or the per- forming rights society limited. warning notice: free datasheet http:///
xd-series (en) 57 knowledge section in case of difficulty what seems to be a malfunction is not always so. before calling for service, check the following table according to the symptom of your trouble. unplug the power cord from the power outlet then, while holding the enter key depressed, plug the power cord again. ? please note that resetting the microcomputer clears the contents stored in and returns and to condition when it left the factory. operation to reset the microcomputer may fall into malfunction (impos- sibility to operate, erroneous display, etc.) when the power cord is unplugged while power is on or due to an external factor. in this case, execute the following procedure to reset the microcomputer and return it to normal condition. sound is not produced. standby and timer indicators blink alternately and no sound is output. sound is not produced from the left or right speakers. the clock display blinks. timer operation is not pos- sible. radio stations cannot be re- ceived. noise interferes. ? the speaker cords are disconnected. ? the mute switch of remote control unit is switched on. ? the headphone plug is inserted into the jack. ? the speaker cords are short-circuited. ? the speaker cords are disconnected. ? the left and right volumes are not balanced. ? there was a power failure. ? the power cord was unplugged from the outlet. ? the present time has not been ad- justed or there was a power failure. ? the timer program or the timer on/ off time has not been set properly. ? the antennas have not been con- nected. ? a proper broadcasting band has not been selected. ? the frequency of the station to be received is not tuned. ? car ignition noise. ? influence of an electric appliance. ? a tv set is installed near the system. ? connect properly referring to sys- tem connection . ? switch mute off. ? unplug the headphone plug. ? turn the power off, remove the short- circuit and turn the power on again. ? connect properly referring to sys- tem connection . ? adjust the left and right volume bal- ance. ? adjust the present time again. ? adjust the present time again. ? adjust the present time referring to clock adjustment . ? check the timer program and set its on/ off time properly. note that everyday and one time cannot be set simulta- neously for a single timer program. ? connect antennas. ? select a band. ? tune to the frequency of the desired station. ? install the outdoor antenna in an apart position from the road. ? switch the suspected electric appli- ance off. ? install the tv or the system at an increased distance between them. enter remedy receiver, speakers cause symptom 9 ( * 9 y p p p e 8 9 (main unit only) free datasheet http:///
xd-series (en) 58 knowledge section in case of difficulty ? the head is dirty. ? the tape is wound too tight due to irregular winding. ? a nonrecorded tape is played. ? the cassette holder is not closed com- pletely. ? the operation key is pressed immedi- ately after closing the cassette holder. ? the operation key is pressed in less than 4 seconds after turning the power on. ? a tape is not inserted in the unit. ? the tape is wound too tight due to irregular winding. ? the tape is fully wound to one of the reels. ? the tape used is not suitable for dpss, for example the spaces between tunes may be too short. ? this is due to the difference in the tape length or characteristics of the mechanisms of two cassette decks. ? the key is pressed during recording or playback. ? the microcomputer is malfunctioning due to external noise. ? the head is dirty. ? the tape is stretched or shrunk. ? clean the head referring to mainte- nance . ? try another tape. ? play a recorded tape. ? close the holder completely. ? press operations keys in more than a few seconds after closing the holder. ? press operation keys after waiting for more than 4 seconds. ? insert a tape. ? try another tape. ? change the tape transport direction or reverse the tape insertion orientation. ? refer to searching for the desired music program (dpss) . ? small time difference does not mean a malfunction. ? press in stop mode. ? reset the microcomputer. ? clean the head referring to mainte- nance . ? try another tape. remedy symptom cause sound cannot be produced by pressing the play key. no operation occurs even when an operation key is pressed. the dpss malfunctions. (xd-5....series only) in dubbing, the tape stops at different moments in decks a and b. the cassette holders cannot be opened by pressing the 0 push open area. sound is harsh or high fre- quencies are not repro- duced. cassette deck no station can be received by preset call operation. demonstration starts sud- denly. power turns off in the middle of operation. ? the frequency of the preset station is not tunable. ? the preset memory has been cleared because the power cord has been unplugged for a long period. ? the power plug was unplugged from the outlet while the power switch was on, or there was a power failure. ? a.p.s. on is set. ? preset stations with tunable frequen- cies. ? preset stations again. ? this is not malfunction. press the display/demo key to cancel the demontration. ? set the a.p.s. off . 1.with some tapes, a squeaky noise is produced when the tape is stopped automatically. this is due to the tape protection function, and not a malfunction. 2.do not use longer tape than 110 minutes tapes, for the tape is too thin and gets easily tangled. notes notes y a a a u y | | 6 r free datasheet http:///
xd-series (en) 59 knowledge section in case of difficulty ? try another tape. ? switch off the equalizer and 3d surround effects before starting playback. ? decrease the input level. ? demagnetize the head referring to maintenance . ? install the system at a distance from other electric appliances and tv. ? switch on the tape equalizer or dolby nr. ? clean the head referring to mainte- nance . ? wind the tape again by fast forward- ing, rewinding or playing from an end to the other. ? use a cassette with an unbroken re- cording protect tab or block the hole. ? close the holder completely. ? select the source to be recorded with the input selector key. ? change the tape transport direction of deck b or reverse the tape insertion orientation. sound is distorted. sound from the md/dvd input (external input) is distorted. noise is noticeable. sound vibrates. recording cannot be started by pressing the record key. remedy symptom cause a cd is placed in the player but it cannot be played. sound is not produced. sound skips. ? the disc is placed upside down. ? the disc position is displaced. ? the disc is extremely dirty. ? the disc is scratched. ? dew is condensed on the optics lens. ? the disc has not been placed. ? the player is not put to the play mode. ? the disc is extremely dirty. ? the disc is scratched. ? the disc is dirty. ? the disc is scratched. ? the player is subject to vibration. ? place the disc properly, with the label side facing upward. ? place the disc properly. ? clean the disc referring to handling of discs and tapes . ? try another disc. ? refer to caution on condensation and remove the condensation by evaporation. ? place a disc in the cd player. ? press the play key. ? clean the disc referring to handling of discs and tapes . ? try another disc. ? clean the disc referring to handling of discs and tapes . ? try another disc. ? install the unit in a place not subject to vibrations. cd player ? the tape being played was recorded with distorted sound. ? a tape which has been recorded with the equalizer and/or 3d surround effects is being played back by applying the equalizer effect. ? the input level is too high. ? the tape head is magnetized. ? external noise is induced. ? a tape which has been recorded with dolby nr is being played back with- out switching the tape equalizer or dolby nr on. ? the capstans or pinch rollers are dirty. ? the tape is wound irregularly. ? the recording protect tab of the cas- sette has been broken. ? the cassette holder is not closed com- pletely. ? the tape input is selected. ? the tape is fully wound to one of the reels. i u y ? y 7 a ? ) ) 7 y ) ) 7 7 free datasheet http:///
xd-series (en) 60 knowledge section remedy symptom cause general remote control operation is not possible. ? batteries are exhausted. ? the remote control is too far away from the system, the controlling angle is deviated or there is an obstacle in between. ? there is no tape or cd set in the component to be played. ? an attempt is made to play the cas- sette deck which is recording some- thing. ? the multi control setting mode is activated. ? replace with new batteries. ? operate the unit inside the remote controllable range. ? set a tape or cd in the component to be played. ? wait until the recording ends. ? cancel the multi control setting mode. remote control unit in case of difficulty remedy symptom cause no operation occurs when an operation key is pressed. ? the multi control setting mode is activated. ? cancel the multi control setting mode. caution : use of controls or adjustments or performance of proce- dures other than those specified herein may result in hazardous radiation exposure. in compliance with federal regulations, following are reproductions of lables on, or inside the product relating to laser product safety. for the u.s.a. location: back panel fcc warning note to catv system installer kenwood corporation 2967-3, ishikawa-cho, hachioji-shi,tokyo, japan kenwood corp. certifies this equipment conforms to dhhs regulations no. 21 cfr 1040.10, chapter 1, subchapter j. this reminder is provided to call the catv system installer's attention to article 820-40 of the nec that provides guide- lines for proper grounding and, in partiqular, specifies that the cable ground shall be connected to the grounding sys- tem of the building, as close to the point of cable entry as practical note: this equipment may generate or use radio frequency energy. changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. the user could lose the authority to operate this equipment if an unauthorized change or modification is made. this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. this equipment may cause harmful interference to radio communications, if it is not installed and used in accor- dance with the instructions. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: CC reorient or relocate the receiving antenna. CC increase the separation between the equipment and receiver. CC connect the equipment into an outlet on a circuit different from that to which the receiver is connected. CC consult the dealer or an experienced radio / tv technician for help. ^ ^ & & free datasheet http:///
xd-series (en) 61 knowledge section specifications [ amplifier section ] (xd-5...series) rated power output (for u.s.a. and canada) 80 watts per channel minimum rms, both channels driven, at 6 w form 40 hz to 15 khz with no more than 0.9 % total harmonic distortion. (ftc) effective output power during stereo operation (except for u.s.a. and canada) 1 khz, 10 % t.h.d., 6 w ............................... 100 w + 100 w rated output power during stereo operation (for u.k., europe and russia) (din) 1 khz, 0.7 % t.h.d., 6 w ........................... 70 w + 70 w (other countories) 1 khz, 1.0 % t.h.d., 6 w ...................................... 80 w + 80 w (xd-4...series) rated power output (for u.s.a. and canada) 50 watts per channel minimum rms, both channels driven, at 6 w form 40 hz to 15 khz with no more than 0.9 % total harmonic distortion. (ftc) effective output power during stereo operation (except for u.s.a. and canada) 1 khz, 10 % t.h.d., 6 w ................................... 70 w + 70 w rated output power during stereo operation (for u.k., europe and russia) (din) 1 khz, 0.7 % t.h.d., 6 w ........................... 50 w + 50 w (other countories) 1 khz, 1.0 % t.h.d., 6 w ...................................... 55 w + 55 w signal to noise ratio md/dvd input .......................................... 90 db (ihf 66) input sensitivity / inpedance md/dvd input .............. (xd-5...series) 270 mv / 47 k w (xd-4...series) 300 mv / 47 k w output level / impedance super woofer preout ..... (xd-5...series) 1.3 v / 620 w (xd-4...series) 1.0 v / 620 w [ tuner section ] fm tuner section tuning frequency range ........................ 87.5 mhz ~ 108 mhz (for russia) .......................................... 65.0 mhz ~ 74.0 mhz mw (am) tuner section tuning frequency range for u.k., europe and russia ................ 531 khz ~ 1,602 khz other countories 9 khz step ........................................... 531 khz ~ 1,602 khz 10 khz step ......................................... 530 khz ~ 1,610 khz for u.s.a. and canada ......................... 530 khz ~ 1,700 khz lw tuner section (for u.k. and russia) tuning frequency range ............................ 153 khz ~ 279 khz sw tuner section (xd-572s only) tuning frequency range ......................... 5.9 mhz ~ 17.9 mhz notes notes 1.kenwood follows a policy of continuous advancements in development. for this reason specifications may be changed without notice. 2.sufficient performance may not be possible at very low temperatures (0c or less). [ cassette deck section ] track ................................................. 4-track, 2-channel stereo recording system ........................................... ac bias system (frequency: 105 khz) heads a deckplayback head ........................................................... 1 b deckplayback / recording head ....................................... 1 erasing head ..................................................................... 1 fast winding time ................................. approx. 115 seconds (c-60 tape) [ cd player section ] laser ....................................................... semiconductor laser wow & flutter ....................... less than unmeasurable limit (except for u.s.a. and canada) digital output (optical) ........................... - 15 dbm ~ - 21 dbm (wave length 660 nm) [ general ] power consumption .............................. (xd-5...series) 200 w (xd-4...series) 150 w dimensions ....................................... w : 280 mm (11) h : 330 mm (13) d : 390 mm (15-3/8) weight (net) ............................. (xd-5...series) 9.9 kg (21.8 lb) (xd-4...series) 9.2 kg (20.2 lb) speakers (ls-n552/ls-n502) xd-5...series enclosure .............. bass-reflex type (magnetically shielded) speaker configuration woofer ................................................. 160 mm, cone type tweeter ................................................... 50 mm, cone type super-tweeter ..................................... 25 mm, dome type impedance .......................................................................... 6 w maximum input level ..................................................... 120 w dimensions ....................................... w : 220 mm (8-11/16) h : 330 mm (13) d : 297 mm (11-11/16) weight (net) ............................... 4.2 kg (9.2 lb) (1 piece) speakers (ls-n452/ls-n402) xd-4...series enclosure .............. bass-reflex type (magnetically shielded) speaker configuration woofer ................................................. 160 mm, cone type tweeter ................................................... 50 mm, cone type impedance .......................................................................... 6 w maximum input level ....................................................... 70 w dimensions ....................................... w : 220 mm (8-11/16) h : 330 mm (13) d : 284 mm (11-3/16) weight (net) ........................................ 4.0 kg (8.8 lb) (1 piece) main unit free datasheet http:///
xd-series (en) 62 knowledge section memo: free datasheet http:///
xd-series (en) 63 knowledge section free datasheet http:///
for your records record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. refer to the model and serial num- bers whenever you call upon your dealer for information or service on this product. model serial number this instruction manual is used to describe multiple models. model availability and features (functions) may differ depending on the country and sales area. digital out jack (optical) 0 xd-572s surround switch/ speakers terminals ! dpss yes yes yes yes xd-502/xd-552 yes (except for u.s.a. and canada) yes (except for u.s.a. and canada) XD-402/xd-452 yes (except for u.s.a., canada, u.k., europe and russia) yes (except for u.s.a. and canada) yes r.d.s. yes (for u.k., europe and russia) yes (for u.k., europe and russia) beat cancel function ? yes (for russia) yes (for russia) tape equalizer yes dolby nr ? yes yes free datasheet http:///

▲Up To Search▲

Price & Availability of XD-402

	To Download XD-402 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .